This section defines the network configuration for the panel. This information is used for message communication over the network.
Note: IP addresses and port numbers may need to be assigned by the network administrator.
Program the Panel at the Keypad
-
Press 6653 (PROG), then CMD at the keypad to enter the PROGRAMMER menu.
-
Press CMD until you see NETWORK OPTIONS, then press any select key or area.
-
Configure the following options as needed:
|
Keypad Display |
Description |
|---|---|
Use IPv6 Address
USE IPV6
|
NO (default) — Do not use IPv6. YES — Use an IPv6 address. Note: IPv6 is DHCP only. |
Use DHCP
NIC 1
|
YES (default) - Use a dynamic IP address. NO — Use a local IP address. |
Local IP Address
NIC1 LOCAL IP
|
Enter the panel’s local IP address. The default is 192.168.0.250. |
Gateway Address
NIC1 GATEWAY
|
Enter the local gateway address. This is needed to exit your local network. The default is 192.168.0.1. |
Subnet Mask
NIC1 SUBNET MASK
|
Enter the local subnet mask assigned to the panel. The default is 255.255.255.000. |
DNS Server
DNS SERVER
|
Enter the IP address of the DNS used by the panel to resolve domain names into IP addresses. The default is 192.168.0.1. Note: The DNS address can be changed (even if the panel has DHCP enabled) on systems with hardwired network connection. |
IPv6 Address
IPV6 ADDRESS |
Enter the IPv6 address. |
IPv6 Gateway Address
IPV6 GATEWAY |
Enter the IPv6 gateway address. |
IPv6 Prefix Bits
IPV6 PREFIX BITS
|
Enter the IPv6 prefix bits. The default is 255. |
IPv6 DNS Server
IPV6 DNS SERVER |
Enter the IPv6 DNS server. |
Enable Dual NIC
ENABLE DUAL NIC?
|
YES (default) — Configure a secondary network connection. NO — Use only the primary network interface. |
Use DHCP (NIC 2)
NIC 2
|
YES (default) — Use a dynamic IP address for NIC 2. NO — Use a local IP address for NIC 2. |
Local IP Address (NIC 2)
NIC2 LOCAL IP
|
Enter the panel’s local IP address for NIC 2. The default is 192.168.0.250. |
Subnet Mask Address (NIC 2)
NIC2 SUBNET MASK
|
Enter the local subnet mask assigned to the panel for NIC 2. The default is 255.255.255.000. |
SCS—VR Passphrase
SCS PASSPHRASE |
Enter the SCS-VR passphrase for NIC 1. |
734N Listen Port
734N LISTEN PORT
|
Enter the port number that the 734N/734N-POE or 8860 Series 7-inch Keypad uses to send communication to the panel. The default is 2002. Note: Ensure the port is programmed the same as the Panel IP Port in Communication programming. The 734N Listen Port cannot be the same as the panel network programming port. |
734N Passphrase
734N PASSPHRASE
|
Enter an 8 to 16-character passphrase to encrypt communication with the 734N/734N-POE. A passphrase is required for operation. The default is blank. Note: Ensure the passphrase matches the 734N Passphrase in Communication programming. |
Enable XR/X1 Communication
ENABLE XR/X1 COMMS?
|
NO (default) — Disable this option. YES — Enable XR to X1 and XR to XR communication. |
XR/X1 Passphrase
XR/X1 PASSPHRASE
|
Enter an 8 to 16-character passphrase to encrypt XR to X1 and XR to XR communication. The default is blank. |
-
When you are finished, continue programming additional menus as needed, or press CMD until STOP displays, then press any select key or area to save the panel programming.
Program the Panel in Dealer Admin
Before You Begin
-
Verify the panel is connected to network
-
Log in to Dealer Admin.
-
Go to Customers, then select the System Name.
-
Go to Programming > Network Options.
-
Configure the following options as needed:
|
Dealer Admin Field |
Description |
|---|---|
Use IPv6
|
Toggle ON to set an IPv6 address. Toggle OFF to disable this option. Note: IPv6 is DHCP only. |
DHCP
|
Toggle ON to use DHCP. Toggle OFF disable this option. |
Local IP Address
|
Enter the panel’s local IP address. The default is 192.168.0.250. |
Gateway Address
|
Enter the local gateway address. This is needed to exit your local network. The default is 192.168.0.1. |
Subnet Mask
|
Enter the local subnet mask assigned to the panel. The default is 255.255.255.000. |
DNS Server
|
Enter the IP address of the DNS used by the panel to resolve domain names into IP addresses. The default is 192.168.0.1. Note: The DNS address can be changed (even if the panel has DHCP enabled) on systems with hardwired network connection. |
IPv6 Address
|
Enter the IPv6 address. |
IPv6 Gateway
|
Enter the IPv6 gateway address. |
IPv6 Prefix Bits
|
Enter the IPv6 prefix bits. The default is 255. |
IPv6 DNS Server
|
Enter the IPv6 DNS server. |
734N Listen Port
|
Enter the port number that the 734N/734N-POE or 8860 Series 7-inch Keypad uses to send communication to the panel. Note: Ensure the port is programmed the same as the Panel IP Port in Communication programming. The 734N Listen Port cannot be the same as the panel network programming port. |
734N Passphrase
|
Enter an 8 to 16-character passphrase to encrypt communication with the 734N/734N-POE. A passphrase is required for operation. The default is blank. Note: Ensure the passphrase matches the 734N Passphrase in Communication programming. |
XR/X1 Communication
|
Toggle ON to enable XR to X1 and XR to XR communication. Toggle OFF to disable this option. |
XR/X1 Passphrase
|
Enter an 8 to 16-character passphrase to encrypt XR to X1 and XR to XR communication. The default is blank. |
|
Dual NIC |
|
Enable Dual NIC
|
Toggle ON to configure a secondary network connection. Toggle OFF to disable this option. |
DHCP
|
Toggle ON to use a dynamic IP address for NIC 2. Toggle OFF to disable this option. |
Local IP Address
|
Enter the panel’s local IP address for NIC 2. The default is 0.0.0.0. |
Gateway Address
|
Enter the local gateway address for NIC 2. This is needed to exit your local network. The default is 0.0.0.0. |
Subnet Mask
|
Enter the local subnet mask assigned to the panel for NIC 2. The default is 0.0.0.0. |
-
When you are finished, select one of the following options:
-
-
If you are finished with all programming — Select Send All Changes at the top of the screen. This sends all programming changes to the panel.
-
If you are finished programming Network Options only — Select the More icon
-