Output Information

This menu allows you to program outputs and configure their settings.

Output Numbers	Description
1-6	Onboard outputs
450-474	Slow response time wireless outputs (activates within 15 seconds)
400-449	Key fobs
480-499	Fast response time wireless outputs (activates within 1 second)
500-999	LX-Bus output, relay output, and zone expansion output
D01-D16	Keypad door strike relay for address 1-16 Refer to Device Addresses for all output numbers.
G1-G20	Output groups

Keypad
Dealer Admin

Program the Panel at the Keypad

Press 6653 (PROG), then CMD at the keypad to enter the PROGRAMMER menu.
Press CMD until you see OUTPUT INFORMATION, then press any select key or area.
Configure the following options as needed:

Keypad Display	Description
Output Number OUTPUT NUMBER	Enter the output number. For wireless output troubles to display at the keypad, specify the keypad address at the Auxiliary 1 Zones option in Status List programming.
Output Name OUTPUT NAME	Enter the a 32-character alphanumerical name for the output number.
Output Real-Time Status OUTPUT REAL-TIME STATUS NO YES	NO (default) — Disable this option. YES — Allow real-time status reports for a hardwired device, such as Output On, Off, Pulse, or Temporal to be sent using Entré, the API connection, and Dealer Admin.
Serial Number SERIAL#: XXXXXXXX ALREADY IN USE OUTPUT NO: XXX	📍 Displays if a Wireless House Code is programmed in System Options and the output number is for a wireless output Enter the 8-digit serial number found on the wireless device. Already In Use, along with the programmed output number, displays when the serial number is already programmed for another output.
Supervision Time SUPRVSN TIME: 240 0 3 60 240	Note: The 3-minute supervision time is only available for 1135 Wireless Sirens. Select the supervision time required for the wireless output. The default is 240 minutes. The transmitter checks in at least once during this time or a missing condition is indicated for that zone. Enter 0 to configure an unsupervised transmitter. When the panel is reset, a receiver is installed or powered down and powered up, programming is complete, the supervision timer restarts for all wireless outputs.
Trip With Panel Bell TRIP WITH PANEL BELL NO YES	📍 Displays if you are programming an 1135 Wireless Siren. YES (default) — Enable the 1135 to follow the panel’s bell output cadence for the zone type and bell cutoff time up to 15 minutes. NO — Disable this option.

When you are finished, continue programming additional menus as needed, or press CMD until STOP displays, then press any select key or area to save the panel programming.

Program the Panel in Dealer Admin

Before You Begin

Verify the panel is connected to network
Log in to Dealer Admin.

Go to Customers, then select the System Name.
Go to Programming > Output Information.
Configure the following options as needed:

Dealer Admin Field	Description
Output Number	Enter the output number. For wireless output troubles to display at the keypad, specify the keypad address at the Auxiliary 1 Zones option in Status List programming.
Output Name	Enter the a 32-character alphanumerical name for the output number.
Serial Number	📍 Displays if a Wireless House Code is programmed in System Options and the output number is for a wireless output Enter the 8-digit serial number found on the wireless device.
Supervision Time	Note: The 3-minute supervision time is only available for 1135 Wireless Sirens. Select the supervision time required for the wireless output. The default is 240 minutes. The transmitter checks in at least once during this time or a missing condition is indicated for that zone. Enter 0 to configure an unsupervised transmitter. When the panel is reset, a receiver is installed or powered down and powered up, programming is complete, the supervision timer restarts for all wireless outputs.
Trip With Panel Bell	📍 Displays if you are programming an 1135 Wireless Siren. Toggle ON to enable the 1135 to follow the panel’s bell output cadence for the zone type and bell cutoff time up to 15 minutes. Toggle OFF to disable this option.
Real-time Status	Toggle ON to allow real-time status reports for a hardwired device, such as Output On, Off, Pulse, or Temporal to be sent using Entré, the API connection, and Dealer Admin. Toggle OFF to disable this option.

When you are finished, select one of the following options:

- If you are finished with all programming — Select Send All Changes at the top of the screen. This sends all programming changes to the panel.
- If you are finished programming Output Information only — Select the More icon , then select Send Output Information. This only sends output changes to the panel.

Last updated: November 05, 2026