System Options

Instant Arming

NO (default) — INSTANT does not display on the arming keypad during arming.

YES — INSTANT displays on the arming keypad for selecting during the exit countdown delay when arming fewer than all system areas.

When INSTANT is selected, entry and exit delays for the areas being armed are ignored. Entry delays for previously armed areas are not affected.

Closing Wait

NO (default) — Disable this option.

YES — The keypad displays ONE MOMENT… while waiting for an acknowledgement from the receiver before arming the selected areas and performing a Bell Test (if selected). Exit delays begin after the Closing Wait.

Entry Delay 1, 2, 3, and 4

Enter the number of seconds (30-250) for the Entry Delay time for all Exit type zones. When an armed Exit zone is faulted, the keypad prewarn tone sounds. Keypads programmed to prewarn for that zone display ENTER CODE:- and the zone name causing the Entry Delay.

Cross Zone Time

Enter the number of seconds (4-240) allowed between zone faults. The default is 4. Enter 0 to disable this option.

When zones are cross-zoned, ensure the same zone or a second cross-zoned zone faults within the programmed time for an Alarm report for both zones to send to the receiver. If the Cross Zone time expires without the second zone faulting, only a zone fault from the first zone is reported.

See Cross Zoning.

Zone Retard Delay

Enter the retard delay time (1-250 seconds) for Fire, Supervisory, Auxiliary 1, Auxiliary 2, Arming, Holdup, and Panic type zones. The default is 10 seconds. Enter 0 to disable this option.

This delay only applies when a zone is shorted. The zone needs to remain shorted for the entire delay period before the panel recognizes the fault.

Power Fail Hours

Enter the number of hours (1-15) AC power can be off before an AC Power Failure report is sent to the receiver.

The default is 1 hour. Enter 0 to disable this option.

Swinger Bypass Trips

Enter the number of times (1-6) a zone can enter an Alarm or Trouble condition within 1 hour before being automatically bypassed. The default is 2. Enter 0 to disable this option.

Bypassed zones are automatically reset when the area they are assigned to is disarmed. All 24-hour zones are reset when any area of the system is disarmed. A Bypass report is sent to the receiver if Bypass Reports is set to Yes.

Reset Swinger Bypass

NO (default) — Disable this option.

YES — Reset the automatically bypassed zone if it remains in a normal condition for 1 hour after being bypassed. A report of the automatic reset is sent to the receiver if Bypass Reports is set to Yes.

Zone Activity Hours

This option monitors activity for a person living alone.

Enter the number of hours (0-9) that can elapse without a disarmed zone being tripped before a message is sent to the receiver. The default is 0, which disables this option.

When the system is disarmed, the activity timer begins counting down. Each time activity occurs, the timer restarts. Before the timer expires, the keypad sounds a tone and displays PRESS ANY KEY, which allows the user to restart the activity timer. The tone duration is determined by the number of seconds programmed for Entry Delay 2.

See Zone Activity Check Messages.

Request Time Change

This option allows the panel to request automatic time changes from SecureCom Wireless or the DMP SCS-1R or SCS-VR Receiver on Path 1. For the SCS receiver to send time changes, program it to send and receive time change updates from the network automation computer at least every 24 hours.

• NO — Do not request time changes.

• SCS — Request time changes from the SCS-1R or SCS-VR receiver.

• SCW — Request time changes from SecureCom Wireless.

• NTP — Request time updates from a Network Time Protocol (NTP) server.

NTP URL

📍 Displays if Request Time Change is NTP.

Enter the NTP URL.

Daylight Saving Time

📍 Displays if Request Time Change is SecureCom or NTP.

NO (default) — Do not observe Daylight Saving Time.

YES — Observe Daylight Saving Time.

Hours from GMT

Enter the number (0-23) that indicates the difference between the Greenwich Mean Time (GMT) and where the panel is located. The default is 6.

See GMT Time Zones.

Latch Supervisory Zones

YES (default) — Enable latch Supervisory zone alarms on the keypad to display until a sensor reset is performed.

NO — Automatically clear Supervisory zone alarms from the keypad display when the zone restores to a normal condition.

Programming Language

Primary Language

Secondary Language

Press CMD to select one of the following primary programming menu languages:

• ENG (default) — English

• SPN — Spanish (ESPANOL)

• FRN — French (FRANCAIS)

• CZE — Czech (CESKY)

• GRE — Greek (Ελληνικά)

• DUT — Dutch (NEDER)

When a secondary programming language is chosen, the installer is prompted to choose the programming language. If this menu is set to None, the option to choose a language does not display,

Select one of the following secondary programming menu languages:

• NONE — (default)

• ENG — English

• SPN — Spanish (ESPANOL)

• FRN — French (FRANCAIS)

• CZE — Czech (CESKY)

• GRE — Greek (Ελληνικά)

• DUT — Dutch (NEDER)

User Language

Primary Language

Secondary Language

Press CMD to select one of the following user menu languages:

• ENG (default) — English

• SPN — Spanish (ESPANOL)

• FRN — French (FRANCAIS)

• CZE — Czech (CESKY)

• GRE — Greek (Ελληνικά)

• DUT — Dutch (NEDER)

When a secondary user language is chosen, the user is prompted to choose the language that displays in the User Menu and Status List when they access the User Menu. If this feature is set to None, the option to choose a language does not display.

Select one of the following secondary programming menu languages:

• NONE — (default)

• ENG — English

• SPN — Spanish (ESPANOL)

• FRN — French (FRANCAIS)

• CZE — Czech (CESKY)

• GRE — Greek (Ελληνικά)

• DUT — Dutch (NEDER)

Bypass Limit

Enter the maximum number of zones (0-8) that can be bypassed in any single area when that area is being armed at a keypad. The default is 0, which disables this feature.

If the number of zones that are not in a normal state or are already bypassed exceeds this limit, the area cannot be armed and Arming Stopped displays.

Wireless House Code

Enter a house code from 1 to 50 to allow the DMP panel, receiver, and transmitters to communicate with one another. The default is 0, which means no wireless system is being used.

The receiver listens for signals from transmitters that have a matching house code and programmed serial number. After you change the house code, allow up to 2 minutes for the transmitters to learn the new code and resume normal operation.

Detect Wireless Jamming

📍 Displays if Wireless House Code is 1-50.

NO (default) — Disable jamming messages.

YES — Enable jamming messages to display in the Status List. When the wireless receiver detects jamming, a jammed trouble (when disarmed) or jammed alarm (when armed) message displays in the Status List and is sent to the monitoring center.

1100 Series Wireless Encryption

📍 Displays if Wireless House Code is 1-50.

Wireless encryption allows the panel to communicate with encrypted 1100 Series wireless devices.

• NONE (default) — Disable this feature.

• ALL — Allow encryption for all wireless devices programmed in the panel.

• BOTH — Allow encryption for all selected wireless devices programmed in the panel.

Wireless Passphrase

📍 Displays if Wireless Encryption is All or Both.

Enter a passphrase to support encrypted 1100 Series wireless devices. The passphrase is an 8-digit hexadecimal number that determines the system’s encryption key.

Trouble Audible Annunciation

This feature allows you to choose when trouble audibles annunciate from the keypad. This also includes Battery Trouble, Panel Tamper, and other system troubles.

DAY (default) — Enable annunciation from 9 AM to 9 PM.

ANY — Enable annunciation anytime.

MIN — Enable annunciation for only Fire and Supervisory zones from 9 AM to 9 PM,

Enable Keypad Panic Keys

This feature allows the panic key operation selected at the keypad to send a Panic, Holdup, Emergency, or Fire message to the monitoring center.

YES (default) — Enable two-button panic operation.

NO — Disable this feature.

Enhanced Zone Test

NO (default) — Disable this option.

YES — Allow enhanced zone test operation for the Walk Test, Panic Test, and Burglary Zone Test in the User Menu. See Test the System.

Enhanced zone operation enables the following options:

• A Verify message sends each time a zone is tested. If a zone is tripped multiple times, a Verify message is sent for each trip to allow the monitoring center to record the number of devices per zone.

• A Verify message for each zone test is sent every time a zone is tripped instead of at the end of the Walk Test.

• The System Test Begin and System Test End monitoring center messages indicate the zone type being tested. The System Test Begin message also includes the user name and number.

Keypad Armed LED

ALL (default) — Require all keypad display areas to arm before the keypad Armed LED turns on.

ANY — Turn on the keypad Armed LED when any keypad display area armed.

Allow Own User Code Change

NO (default) — Leave this option disabled.

YES — Allow users without user code authority to change their own user codes. When enabled, the User Code option in the User Menu displays USER CODE ****** at the keypad to allow users to change their own codes.

Panic Supervision

NO — Disable this option.

YES — Enable 30-day supervision for the 1144 Series Key Fob.

This feature allows a lost key fob or one with a dead battery to be identified as a missing transmitter by the monitoring center’s host automation system without requiring a Supervision Time to be programmed in Zone Information.

The key fob automatically sends a supervision message to the receiver every 4 hours, which resets the 30-day countdown timer for the key fob serial number. If the 30-day timer expires, the receiver sends a Zone Missing message to the host automation system.

Weather Zip Code

This feature enables the keypad to display local U.S.A weather updates. Enter your zip code to use this option. The default is 0, which disables this option.

If you are using a 7800 or 8800 Series Keypad, the current weather conditions and the next day’s forecast display as graphics on the main screen. All other DMP keypads display the weather information in the Status List.

Instant Arming

Toggle ON to allow INSTANT to display on the arming keypad for selecting during the exit countdown delay when arming fewer than all system areas.

When INSTANT is selected, entry and exit delays for the areas being armed are ignored. Entry delays for previously armed areas are not affected.

Toggle OFF to disable this option.

Closing Wait

Toggle ON to display ONE MOMENT… at the keypad while waiting for an acknowledgement from the receiver before arming the selected areas and performing a Bell Test (if selected). Exit delays begin after the Closing Wait.

Toggle OFF to disable this option.

Entry Delay 1

Entry Delay 2

Entry Delay 3

Entry Delay 4

Enter the number of seconds (30-250) for the Entry Delay time for all Exit type zones. When an armed Exit zone is faulted, the keypad prewarn tone sounds. Keypads programmed to prewarn for that zone display ENTER CODE:- and the zone name causing the Entry Delay.

Cross Zone Time

Enter the number of seconds (4-240) allowed between zone faults. The default is 4. Enter 0 to disable this option.

When zones are cross-zoned, ensure the same zone or a second cross-zoned zone faults within the programmed time for an Alarm report for both zones to send to the receiver. If the Cross Zone time expires without the second zone faulting, only a zone fault from the first zone is reported.

See Cross Zoning.

Zone Retard Delay

Enter the retard delay time (1-250 seconds) for Fire, Supervisory, Auxiliary 1, Auxiliary 2, Arming, Holdup, and Panic type zones. The default is 10 seconds. Enter 0 to disable this option.

This delay only applies when a zone is shorted. The zone needs to remain shorted for the entire delay period before the panel recognizes the fault.

Power Fail Delay

Enter the number of hours (1-15) AC power can be off before an AC Power Failure report is sent to the receiver.

The default is 1 hour. Enter 0 to disable this option.

Swinger Bypass Trips

Enter the number of times (1-6) a zone can enter an Alarm or Trouble condition within 1 hour before being automatically bypassed. The default is 2. Enter 0 to disable this option.

Bypassed zones are automatically reset when the area they are assigned to is disarmed. All 24-hour zones are reset when any area of the system is disarmed. A Bypass report is sent to the receiver if Bypass Reports is set to Yes.

Reset Swinger Bypass

Toggle ON to reset the automatically bypassed zone if it remains in a normal condition for 1 hour after being bypassed. A report of the automatic reset is sent to the receiver if Bypass Reports is set to Yes.

Toggle OFF to disable this option.

Zone Activity Hours

This option monitors activity for a person living alone.

Enter the number of hours (0-9) that can elapse without a disarmed zone being tripped before a message is sent to the receiver. The default is 0, which disables this option.

When the system is disarmed, the activity timer begins counting down. Each time activity occurs, the timer restarts. Before the timer expires, the keypad sounds a tone and displays PRESS ANY KEY, which allows the user to restart the activity timer. The tone duration is determined by the number of seconds programmed for Entry Delay 2.

See Zone Activity Check Messages.

Update Time With

This option allows the panel to request automatic time changes from SecureCom Wireless or the DMP SCS-1R or SCS-VR Receiver on Path 1. For the SCS receiver to send time changes, program it to send and receive time change updates from the network automation computer at least every 24 hours.

• No Time Change — Do not request time changes.

• Receiver — Request time changes from the SCS-1R or SCS-VR receiver.

• SecureCom — Request time changes from SecureCom Wireless.

• NTP — Request time updates from a Network Time Protocol (NTP) server.

NTP Server URL

📍 Displays if Update Time With is NTP.

Enter the NTP URL.

Observe DST

📍 Displays if Update Time With is SecureCom or NTP.

Toggle ON to observe Daylight Saving Time.

Toggle OFF to disable this option.

Hours from GMT

Enter the number (0-23) that indicates the difference between the Greenwich Mean Time (GMT) and where the panel is located. The default is 6.

See GMT Time Zones.

Latched Supervisory Zones

Toggle ON to enable latched Supervisory zone alarms on the keypad to display until a sensor reset is performed.

Toggle OFF to automatically clear Supervisory zone alarms from the keypad display when the zone restores to a normal condition.

Primary Programming Language

Select one of the following primary programming menu languages:

• English

• Spanish (Espanol)

• French (Francais)

• Czech (Cesky)

• Greek (Ελληνικά)

• Dutch (Neder)

Secondary Programming Language

When a secondary programming language is chosen, the installer is prompted to choose the programming language. If this menu is set to None, the option to choose a language does not display,

Select one of the following secondary programming menu languages:

• English

• Spanish (Espanol)

• French (Francais)

• Czech (Cesky)

• Greek (Ελληνικά)

• Dutch (Neder)

Primary User Language

Select one of the following user menu languages:

• English

• Spanish (Espanol)

• French (Francais)

• Czech (Cesky)

• Greek (Ελληνικά)

• Dutch (Neder)

Secondary User Language

When a secondary user language is chosen, the user is prompted to choose the language that displays in the User Menu and Status List when they access the User Menu. If this feature is set to None, the option to choose a language does not display.

Select one of the following secondary programming menu languages:

• English

• Spanish (Espanol)

• French (Francais)

• Czech (Cesky)

• Greek (Ελληνικά)

• Dutch (Neder)

Bypass Limit

Enter the maximum number of zones (0-8) that can be bypassed in any single area when that area is being armed at a keypad. The default is 0, which disables this feature.

If the number of zones that are not in a normal state or are already bypassed exceeds this limit, the area cannot be armed and Arming Stopped displays.

Wireless House Code

Enter a house code from 1 to 50 to allow the DMP panel, receiver, and transmitters to communicate with one another. The default is 0, which means no wireless system is being used.

The receiver listens for signals from transmitters that have a matching house code and programmed serial number. After you change the house code, allow up to 2 minutes for the transmitters to learn the new code and resume normal operation.

Detect Wireless Jamming

📍 Displays if Wireless House Code is 1-50.

Toggle ON to enable jamming messages to display in the Status List.

When the wireless receiver detects jamming, a jammed trouble (when disarmed) or jammed alarm (when armed) message displays in the Status List and is sent to the monitoring center.

Toggle OFF to disable jamming messages.

Trouble Audibles

This feature allows you to choose when trouble audibles annunciate from the keypad. This also includes Battery Trouble, Panel Tamper, and other system troubles.

Day (default) — Enable annunciation from 9 AM to 9 PM.

Any — Enable annunciation anytime.

Min — Enable annunciation for only Fire and Supervisory zones from 9 AM to 9 PM.

Enable Keypad Panic Keys

This feature allows the panic key operation selected at the keypad to send a Panic, Holdup, Emergency, or Fire message to the monitoring center.

Toggle ON to enable two-button panic operation.

Toggle OFF to disable this feature.

Enhanced Zone Test

Toggle ON to allow enhanced zone test operation for the Walk Test, Panic Test, and Burglary Zone Test in the User Menu. See Test the System.

Enhanced zone operation enables the following options:

• A Verify message sends each time a zone is tested. If a zone is tripped multiple times, a Verify message is sent for each trip to allow the monitoring center to record the number of devices per zone.

• A Verify message for each zone test is sent every time a zone is tripped instead of at the end of the Walk Test.

• The System Test Begin and System Test End monitoring center messages indicate the zone type being tested. The System Test Begin message also includes the user name and number.

Toggle OFF to disable this option.

Keypad Armed LED

All — Require all keypad display areas to arm before the keypad Armed LED turns on.

Any — Turn on the keypad Armed LED when any keypad display area armed.

Allow Own User Code Change

Toggle ON to allow users without user code authority to change their own user codes. When enabled, the User Code option in the User Menu displays USER CODE ****** at the keypad to allow users to change their own codes.

Toggle OFF to disable this option.

Panic Supervision

Toggle ON to enable 30-day supervision for the 1144 Series Key Fob.

This feature allows a lost key fob or one with a dead battery to be identified as a missing transmitter by the monitoring center’s host automation system without requiring a Supervision Time to be programmed in Zone Information.

The key fob automatically sends a supervision message to the receiver every 4 hours, which resets the 30-day countdown timer for the key fob serial number. If the 30-day timer expires, the receiver sends a Zone Missing message to the host automation system.

Toggle OFF to disable this option.

Weather Zip Code

This feature enables the keypad to display local U.S.A weather updates. Enter your zip code to use this option. The default is 0, which disables this option.

If you are using a 7800 Series Keypad, the current weather conditions and the next day’s forecast display as graphics on the main screen. All other DMP keypads display the weather information in the Status List.

1100 Wireless Encryption

📍 Displays if Wireless House Code is 1-50.

Wireless encryption allows the panel to communicate with encrypted 1100 Series wireless devices.

• None — Disable this option.

• Both — Allow encryption for all selected wireless devices programmed in the panel.

• All — Allow encryption for all wireless devices programmed in the panel.

1100 Wireless Encryption Passphrase

📍 Displays if Wireless Encryption is All or Both.

Enter a passphrase to support encrypted 1100 Series wireless devices. Dealer Admin automatically generates an 8-digit hexadecimal passphrase that determines the system’s encryption key.